[Acoustics] StreamPro issue

[Lloyd T Brooks]

Lindsay, You need to run the INI2XML program to create the w.000 file 
before you startup WinRiver in the office.  The w.000 file from INI2XML 
should contain the edge and transducer depth values.  Make sure the 
INI2XML program is located on your C: drive and not on the desktop.  I 
found out the hard way that if the program is on the desktop it will run 
but none of the edge and transducer depth values will not be transfered to 
the .w000 file. 
Hope this helps, Tim
P.S. Say hey to Ron for me.
-------------------------------
L. Timothy Brooks
U. S. Geological Survey, WRD
425 Jordan Rd
Troy, NY 12180-8349
Phone# 518/285-5644
Fax# 518/285/5601
ltbrooks at usgs.gov



Michael S Rehmel <msrehmel at usgs.gov> 
Sent by: acoustics-bounces at simon.er.usgs.gov
11/01/2005 07:09 AM

To
Lindsay J Pickrell <pickrell at usgs.gov>
cc
acoustics at simon.er.usgs.gov
Subject
Re: [Acoustics] StreamPro issue







Lindsay, 

My guess is that you are having the following problem: 
If you load a StreamPro raw data file in WinRiver before you successfully 
converting the .xml file to a *w.000 file, WinRiver will create a *w.001 
that contains default settings for all values. If you later successfully 
convert the .xml to *w.000 you still will not see the original transects 
settings in WinRiver because the *w.001 configuration settings will 
overwrite the *w.000 settings. If this happens delete the *w.001 
configuration file and make sure that the *w.000 file exists before 
loading the corresponding raw data file in WinRiver. 

I hope this is clear enough to help, 

Mike 

________________________________________________

Michael S. Rehmel                phone: 317.290.3333 ext 158
U.S. Geological Survey              fax: 317.290.3313
5957 Lakeside Blvd.               email: msrehmel at usgs.gov
Indianapolis, IN  46278             web: http://in.water.usgs.gov
________________________________________________
  


Lindsay J Pickrell <pickrell at usgs.gov> 
Sent by: acoustics-bounces at simon.er.usgs.gov 
10/31/2005 06:38 PM 


To
acoustics at simon.er.usgs.gov 
cc

Subject
[Acoustics] StreamPro issue









A few of us at the Anchorage field office have been using the StreamPro 
quite a bit lately and have found that it doesn't always copy all of the 
data from the configuration file over into WinRiver.  I've seen the 
profiler depth and edge estimates erased when .xml files are converted to 
WinRiver, giving you different section discharges.  If you re enter your 
transducer depth and edge estimates into WinRiver it will compute the same 
discharge that was recorded in the field.  I have had several successfull 
conversions to WinRiver with no problems so I am not sure when this 
occurs.  It may be a good idea to make sure your discharges match those 
recorded in the field when using this program to convert StreamPro .xml 
files to WinRiver.   

Lindsay_______________________________________________
Acoustics mailing list
Acoustics at simon.er.usgs.gov
http://simon.er.usgs.gov/mailman/listinfo/acoustics
_______________________________________________
Acoustics mailing list
Acoustics at simon.er.usgs.gov
http://simon.er.usgs.gov/mailman/listinfo/acoustics

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://simon.er.usgs.gov/pipermail/acoustics/attachments/20051101/58d9c149/attachment.html